Skip to content

How To Use Concrete Deck Blocks

Concrete deck blocks are an easy way to create a foundation for a deck. The blocks are placed on the ground in a square or rectangle, and the deck is built on top of them. This type of foundation is quick and easy to install, and it is much less expensive than traditional foundations.

How To Use Concrete Deck Blocks

Concrete deck blocks are a great way to build a deck without having to hire a professional. They are very simple to use and can be done by anyone with a little bit of experience. Here is how you can use them: 1. Decide where you want your deck to be. 2. Measure the area and purchase the correct amount of concrete deck blocks. 3. Dig four holes in the ground that are large enough for the blocks to fit in

Concrete deck blocks are a quick and easy way to create a deck. The blocks are typically made of cinder block or concrete and have pre-drilled holes in them for the screws that will hold the decking in place. Decking can be either wood or composite, and most types of screws can be used to attach it to the blocks.

  • Spread concrete in each block, using a trowel
  • Place the blocks on level ground, with the wider side facing down
  • Smooth the surface and allow the concrete to cure for 24 hours. place the

1. Types of concrete deck blocks 2. How to use them to build a deck 3. What are some benefits of using concrete deck blocks? 1. There are several types of concrete deck blocks on the market, so it’s important to select the right type for the project at hand. 2. To use concrete deck blocks to build a deck, start by placing four blocks in a square formation. Then, place a fifth block in the middle of


Frequently Asked Questions

How Do You Set Deck Blocks?

There are a few ways to set deck blocks, but the most common is to use a batterboard and strings. First, lay out the location of your deck and mark the corners. Next, drive stakes into the ground at each corner and tie a string between them. Finally, place your deck blocks on top of the strings and adjust as needed.

Are Concrete Deck Blocks Good?

There is no definitive answer, as it depends on the situation. Concrete deck blocks can be a good option in some cases, but not in others. For example, they are often a good choice for decks that are not going to be heavily used, or for decks that are being built on a relatively level surface. However, if the deck is going to be used heavily or if there is a lot of variance in the surface on which it is being built, then using concrete deck blocks may not be the best option.

What Goes Under Deck Blocks?

Under deck blocks are a type of block used to support the decking boards in a deck. They are usually made of concrete and come in various sizes and shapes.

How Do You Set Concrete Deck Blocks?

There are a few ways to set concrete deck blocks, but the most common is by using a straight edge and line level to ensure each block is level. The blocks can then be secured in place with stakes or rebar.

How Far Apart Should You Put Deck Blocks?

There is no correct answer to this question as it depends on the specific project requirements. However, a good rule of thumb is to space deck blocks about 12 inches (30 cm) apart.

How Many Deck Blocks Do I Need For A 10X10 Shed?

You would need 10 deck blocks for a 10×10 shed.

How Many Deck Blocks Do I Need For A 10X10 Deck?

There are 100 deck blocks in a 10X10 deck, so you would need 10 rows of 10 blocks.

How Do You Anchor A Deck Block?

There are a few ways to anchor a deck block. One way is to use metal brackets that are screwed into the deck frame and the block. Another way is to use special lag bolts that go through the deck frame and embed themselves in the block.

Where Should Deck Blocks Be Placed?

There is no one definitive answer to this question. Deck blocks can be placed pretty much anywhere, as long as they are level and stable. Some people prefer to place them near the house, while others prefer to place them further away. It really depends on your personal preference and the layout of your property.

What Goes Under A Deck Block?

A deck block is a rectangular piece of wood that sits atop the posts that support a deck and transfers the weight of the deck to the posts.

How Far Apart Do You Place Deck Blocks?

There is no solid answer to this question as it depends on the specific project at hand. Generally, deck blocks should be placed 16-24 inches apart, but this can vary depending on the block’s size and weight.

How Far Apart Should You Place Deck Blocks?

There is no definitive answer to this question as it depends on a number of factors, such as the size and shape of the deck, the weight of the materials you plan to use, and the type of soil your deck is built on. Generally, you should place deck blocks at least 16 inches apart, but it’s a good idea to consult with an expert or do some research online to get a more specific recommendation for your project.


To Summarize

Concrete deck blocks are a popular way to create a deck without having to pour concrete footings. The blocks can be stacked and then the decking is attached.

Leave a Reply

Your email address will not be published.